Soleus Air Fan FS2 40R 32 User Manual

16” Stand Fan with Remote Control  
Model No: FS2-40R-32  
Operating Instructions  
3072986  
FS2-40R-32  
© 2011 Soleus Air International  
 
WARNING: This fan is equipped with a polarized plug (one blade is wider than the other). The plug is in-  
tended to fit into a power outlet only one way, with the wide blade in the wide slot. This is a safety feature; if  
you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still does not fit, contact  
a qualified electrician.  
DO NOT DEFEAT THE SAFETY PURPOSE OF THE POLARIZED PLUG.  
TECHNICAL SPECIFICATIONS  
Voltage Rating  
Power Consumption  
Unit Size  
115V, 60Hz  
55W  
17.5 in. (W) x 17 in. (D) x 53 in. (H)  
14 lbs  
Unit Weight  
3
 
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit  
situation. If the fuse blows, unplug the product from the outlet. Replace the fuse per the instructions  
below and check the product. If the replacement fuse blows, a short-circuit may be present and the  
product should be discarded or returned to an authorized service facility for examination and/or  
repair.  
HOW TO REPLACE THE FUSE  
1. Unplug the fan from the outlet. Place the plug on a firm, flat surface.  
Open the fuse cover, located on the top of the plug, using your thumb  
or a flathead screwdriver to slide the over towards the prongs.  
NOTE: Ensure that the fuse cover is completely open before attempting  
to remove the fuse.  
2. Remove the fuse carefully by using a small screwdriver to pry the fuse  
out of the compartment by the metal ends of the fuse.  
3. Risk of fire. Insert a new 5 Amp, 125 Volt fuse into the fuse compart-  
ment, making sure that the fuse is securely in place.  
4. Slide the fuse cover closed completely. If the fuse cover is difficult to  
close, make sure the fuse is properly secured in place by pressing  
down on the metal ends of the fuse.  
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a  
safety device (fuse) that should not be removed. Do not use the product if  
the attachment plug is damaged.  
To avoid a risk of fire, only replace with a 5 Amp, 125 Volt fuse.  
To order a new fuse, contact Soleus Air at: (888) 975-5387  
4
 
ASSEMBLY  
WARNING: DO NOT plug in fan before assembly.  
Tools required: Phillips screwdriver (not included)  
Base Assembly:  
1. Unscrew the two screws from the neck of the fan head. Slide the neck of the fan head over the pole of the  
stand, aligning the screw holes. Secure the pole by inserting and tightening the two screws.  
2. Turn the stand upside down and place the base over the bottom of the stand. Align the pre-drilled holes  
on the bottom of the base with the stand. Use the 4 included screws to secure the stand to the base.  
Fan Head Assembly:  
Unscrew the mounting nut counter clockwise from the motor shaft.  
Position the back grill over the motor shaft, fitting the holes in the  
back grill over the knobs that protrude from the front of the mo-  
tor. Make sure the rear grill fits securely against the motor housing.  
Secure the back grill by screwing on the mounting nut. Turn clockwise  
and tighten firmly.  
Slide the fan blade onto the motor shaft with the fan blade’s shaft  
sleeve facing the motor. Make sure the groove in the shaft sleeve  
fits over the spring bolt on the motor shaft.  
Attach the fan blade by screwing the securing knob onto the motor  
shaft counter clockwise.  
Position front grill so logo is horizontal. Attach the grills together by  
positioning the top tab of the front grill over the back grill. Firmly  
press the black ring of the front grill onto the back grill, snapping  
into place. This completes the assembly.  
5
 
OPERATING INSTRUCTIONS  
Using Fan Controls  
1. Set the fan on a stable, level surface.  
2. Turn the fan on by pressing the POWER/SPEED button on the Control Panel or Remote Control.  
3. Adjust the speed setting by pressing the POWER/SPEED on the Control Panel or remote control.  
4. Pressing the MODE button on either the fan or the remote will choose the desired wind mode: Standard,  
Sleep, & Natural. In standard mode the fan operates at a steady speed. In Sleep mode the fan decreases  
speed in the middle of the oscillation pattern. Natural mode simulates the wind by randomly alternating the  
fan speed.  
5. To oscillate the fan head, press the OSCILLATION button located on the fan or the SWING button on the  
remote. Each press of the oscillation button will change the oscillation pattern. You can choose between  
side-to-side, up and down, and figure 8 oscillation patterns  
6. This fan includes a 12 hour auto shut-off timer. To operate the timer, press the TIMER button (located on  
the fan or on the remote) until the desired time is visible on the LCD Display. Each button press will  
increase the time by 1 hour increments. Once the timer is set the you will see “HR” and a clock icon light  
up on the display. Once set, the timer will count down to zero and turn off the fan.  
7. To turn the fan off, press the POWER/SPEED button on the Control Panel or remote control until the unit  
turns off.  
Using the Auto-on Feature  
1. First turn the fan on by pressing the POWER/SPEED button on the Control Panel or Remote Control. You  
will see the current room temperature flashing on and off on the LCD display.  
2. Once the fan is on, press the AUTO button located on the remote control or the control panel.  
3. “AUTO” should now be displayed on the LCD display and the current room temperature will stop flashing  
on the display. When the fan is in auto mode, it will vary speeds according to the room temperature. When  
the room temperature is below 68° the fan will be in standby mode (off). When the temperature is between  
68° F and 74° F the fan will operate at low speed (1). When the temperature is between 75° F and 81° F the  
speed will increase to medium (2). The fan will operate at high speed (3) once the room temperature is  
equal to or greater than 82° F.  
Adjusting Height and Fan Head Tilt  
1. To adjust the height of the fan, turn the Adjustable Height Knob (L) counter-clockwise to loosen the  
stand. Adjust the fan to the desired height, then firmly tighten to secure into place.  
2. To adjust the tilt on the Fan Head, grasp the fan head and push back or pull forward to achieve the  
desired tilt.  
6
 
CLEANING & MAINTENANCE  
1. Turn the fan off and unplug the unit.  
2. Wipe the fan down with a damp cloth for most efficient operation.  
3. Air dry the fan completely before use.  
4. Never use abrasive cleaning agents or solvents. This may cause damage or deterioration to the surface of  
the unit.  
5. Do not immerse the fan in any form of liquid. Do not allow water to drip on or into the fan motor  
housing.  
Fan Blade Cleaning:  
Make certain the fan is unplugged. Unlock the metal clips on the front grill and remove the front grill. Use  
a Phillips screwdriver to loosen the securing screw and remove the fan blade.  
The fan blade and grill may be cleaned with a damp cloth and mild detergent.  
Reassemble the fan after the parts have dried completely. To do so, replace the fan blade, tighten the  
securing screw, and secure the front grill. Do not plug the fan into an electrical outlet until it is fully  
reassembled.  
STORAGE  
If the fan will not be used for a long period of time, store it in a cool, dry location when not in use. To  
prevent dust and dirt build-up, use the original packaging to repack the unit.  
OVERHEAT PROTECTION  
A thermostat is built-in to the motor to prevent overheating. If the fan temperature exceeds the limit on the  
thermostat, the fan will automatically shut-off to prevent overheating and protect the fan components from  
damage.  
REMOTE CONTROL  
The supplied remote uses 2 “AAA” batteries. The remote will work at a distance of roughly 25 feet, and an  
angle of 60°.  
7
 
WARRANTY  
One Year Limited Warranty  
Soleus International Inc. warrants the accompanying Soleus Air FS2-40R-32 16” Stand Fan to be free of defects in ma-  
terial and workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the  
date of original retail purchase in the United States.  
If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of  
charge within a reasonable time after the unit is returned during the warranty period.  
As a condition to any warranty service obligation, the consumer must present this Warranty Certificate along with a  
copy of the original purchase invoice.  
THIS WARRANTY DOES NOT COVER:  
Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in  
material or workmanship.  
Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions  
in the instructions. This includes dents, accidental or otherwise, to the base and head of the unit.  
Damage to the finish of the case, or other appearance parts caused by wear.  
Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus  
International Inc.  
Freight and Insurance cost for the warranty service.  
ALL WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO  
ONE-YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY. SOLEUS INTERNATIONAL INC.  
DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT  
SHALL SOLEUS INTERNATIONAL INC’S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR  
BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT.  
This warranty covers only new products purchased from our authorized dealers or retailers. It does not cover used, sal-  
vaged, or refurbished products.  
As some states do not allow the limitation or exclusion of incidental or consequential damages, or do not allow  
limitation on implied warranties, the above limitations and exclusions may not apply to you. This warranty gives you  
specific legal rights, and you may also have other rights that vary from state to state.  
For Technical Support & Warranty Service  
Please Call (888) 876-5387  
Or Write To:  
Soleus International Inc.  
20035 E. Walnut Dr. North,  
City of Industry, CA 91789 USA  
8
 

Sennheiser TV Antenna ASA 3000 User Manual
Sensory Science DVD Player DDV9150 User Manual
Sharp Refrigerator SJ RM323T User Manual
Sierra Monitor Corporation Carbon Monoxide Alarm 4011 Series User Manual
Singer Sewing Machine 112 3 User Manual
Sony Digital Camera DSC H2 H5 User Manual
Sony Security Camera Network Video Monitoring User Manual
Stinger Automobile Accessories SGN20 User Manual
Sunbeam Microwave Oven SMW610 User Manual
TANDBERG TV Mount 2000MXP User Manual